viewtopic.php?p=998884#p998884
I did have some issues getting things to work with the Master side having "put-stations-in-bridge=none" but after putting station into the bridge (on all sides)it feels like it worked.. I disabled the 60g and noticed that the link failed over and noticed in the bonding tab that is was switching accordingly from 60 as the active link to the wlan1.
I believe the key that led this to work was only having the bonding interface setup on the client (station sides)
If possible id appreciate any insight to make sure my config is right.
Master
Code: Select all
/interface bridge
add admin-mac=18:FD:74:84:9A:DC auto-mac=no comment=defconf name=bridge
/interface w60g
set [ find ] disabled=no isolate-stations=no name=wlan60-1 password=xxxxxxxx \
put-stations-in-bridge=bridge region=usa ssid=br60wapac3
/interface w60g station
add mac-address=18:FD:74:84:9A:DD name=wlan60-station-1 parent=wlan60-1 \
remote-address=18:FD:74:84:AA:5B
add mac-address=18:FD:74:84:9A:DD name=wlan60-station-2 parent=wlan60-1 \
remote-address=18:FD:74:84:AA:16
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
add authentication-types=wpa2-psk mode=dynamic-keys name=redAB \
supplicant-identity="" wpa2-pre-shared-key=xxxxxxxx
/interface wireless
set [ find default-name=wlan1 ] band=5ghz-a/n/ac channel-width=20/40/80mhz-XXXX \
disabled=no frequency=auto installation=outdoor mode=ap-bridge \
security-profile=redAB ssid=br60wapac3
/interface bridge port
add bridge=bridge comment=defconf interface=ether1
add bridge=bridge interface=wlan60-1
add bridge=bridge interface=wlan1
/ip address
add address=10.10.10.26/23 comment=defconf interface=bridge network=10.10.10.0
/ip dns
set servers=8.8.8.8
/ip route
add distance=1 gateway=192.168.2.1
/system clock
set time-zone-autodetect=no time-zone-name=America/New_York
/system identity
set name=60AC-WAP3-Cube-10.26
/system ntp client
set enabled=yes primary-ntp=40.119.6.228
/tool romon
set enabled=yes
Code: Select all
/interface bridge
add admin-mac=18:FD:74:84:AA:15 auto-mac=no comment=defconf name=bridge
/interface w60g
set [ find ] disabled=no mode=station-bridge name=wlan60-1 password=xxxxxxx put-stations-in-bridge=\
bridge region=usa ssid=br60wapac3
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
add authentication-types=wpa2-psk mode=dynamic-keys name=redAB supplicant-identity="" \
wpa2-pre-shared-key=xxxxxxx
/interface wireless
set [ find default-name=wlan1 ] band=5ghz-a/n/ac channel-width=20/40/80mhz-Ceee disabled=no frequency=\
5765 installation=outdoor mode=station-bridge security-profile=redAB ssid=br60wapac3
/interface bonding
add mode=active-backup name=bonding1 primary=wlan60-1 slaves=wlan60-1,wlan1
/snmp community
add addresses=::/0 name=bigredsnmp
/interface bridge port
add bridge=bridge comment=defconf interface=ether1
add bridge=bridge interface=bonding1
/ip address
add address=10.10.10.27/23 comment=defconf interface=bridge network=10.10.10.0
/ip dns
set servers=8.8.8.8,1.1.1.1
/ip route
add distance=1 gateway=10.10.10.1
/snmp
set enabled=yes trap-community=bigredsnmp trap-version=2
/system clock
set time-zone-name=America/New_York
/system identity
set name=60-5-FailOverStation-10.27
/system ntp client
set enabled=yes primary-ntp=40.119.6.228
Code: Select all
/interface bridge
add admin-mac=18:FD:74:84:AA:5A auto-mac=no comment=defconf name=bridge
/interface w60g
set [ find ] disabled=no mode=station-bridge name=wlan60-1 password=xxxxxxxx \
put-stations-in-bridge=bridge region=usa ssid=br60wapac3
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
add authentication-types=wpa2-psk mode=dynamic-keys name=redAB \
supplicant-identity="" wpa2-pre-shared-key=xxxxxxx
/interface wireless
set [ find default-name=wlan1 ] band=5ghz-a/n/ac channel-width=20/40/80mhz-XXXX \
disabled=no frequency=auto installation=outdoor mode=station-bridge \
security-profile=redAB ssid=br60wapac3
/interface bonding
add mode=active-backup name=bonding1 primary=wlan60-1 slaves=wlan60-1,wlan1
/snmp community
add addresses=::/0 name=bigredsnmp
/interface bridge port
add bridge=bridge comment=defconf interface=ether1
add bridge=bridge interface=bonding1
/ip address
add address=10.10.10.28/23 comment=defconf interface=bridge network=10.10.10.0
/ip route
add distance=1 gateway=10.10.10.1
/snmp
set enabled=yes trap-community=bigredsnmp
/system identity
set name=60-5-FailOverStation-10.28